4x 306 Cyclone Alloy Wheels For Sale!!

Not in the best condition, but perfect if you plan on refurbishing and custom spray/powder coating them

All 4 wheels have kerbing/paint flake to varying degrees. 3 decent tyres, one will need replacing. The wheels are sound - no buckling

Open to offers

Must state a price

Rightio.... But I genuinely don't have a clue what they're worth in this condition!?!

I sold a set in similar condition for £60.

I'll be interested at that sort of money

I was hoping to cover the cost of a set of spacers I need to buy which are £80

what spacers do u need???

15mm. I already have 25mm, but they bring the wheels out a little too far on the back resulting in rubbing when I have a full car. I'm hoping than with 15mm they'll sit far enough in the arch to avoid the rubbing

I'll have a pair of 25mm KEI spacers to sell too, once I buy the 15s if anyones interested

If you like i can have the spacers pulled done in a lathe for you to the right width I.E ET15 which is great for the 306 (for a 7" width rim)

What are the wheel dimensions ?

Width =
Diameter =
offset =

I'll work out then what the ideal spacer size would be then

P.S I've just bought an arch roller if you want to try that and keep with the 25mm spacers

Interesting! Thanks Simon

The wheels are 307 Arianes - do you know the dimensions? If not, I'll try and find out

I've had the car lowered a little on the back, but I want it lowered more. But I can't do it yet due the the rubbing - I'm hoping that 15mm spacers will take them in enough

Which year 307 they from?

older 1s are ET32 newer 1s are ET37 iirc

for the older you'd need 17mm spacer and newer 22mm

those are figures for lowering the car past 40-50mm so it doesn't rub on inner arch and i'd say would still be fine on outer arch

I bought them individually on eBay, so I bet I have a miss match I'll check them now

Out of interest, how much to have them machined down on the lathe? And would I need new bolts then?

Thanks Simon

I'll have a word with the father in law see how much he'd want mate

bolts should be fine, if you drive the car down we can check how they go on and make sure they dont go through too far, if they do we can cut a bit off the end and tapper it so is starts fine

Simon, I've just checked and on the back of both rear wheels I have '6 1/2Jx16 CH4-31'

Which matches up with the dimensions found here for Arianes: http://www.peugeot.ie/templates/peugeot2010/downloads/PEUGEOT_ALLOY_WHEELS-2009.pdf

Does that mean I have ET31s!?!? If so, what size spacers would you recommend?

Yeah they are 31mm offset so 16mm would give you an ET15 offset which would be perfect

Brilliant. I take it I'll get away with 15mm? Ive been offered a set for cheap

yeah 15mm would be fine

Thanks for all your advice Gunge. Much appreciated

Now, anyone want to buy a set of Cyclones? £80 collected

Good price mate but i have 3 sets sat in my shed now

I am fairly certain my missus and parents will kill me if I buy yet another set of wheels, altgough they would be good to refurb and sell on... Hmm I shall have to think about this, are there any chunks taken out of the wheel or is it just paint damage?

I want to be as honest as possible. There's a fair bit of kerbing, but most of it is simple enough to put right when refurbishing

However, there's one chunk which is worse than the rest. I imagine this will need to be ground back a little, then filled with that metal filler stuff. I MAY have a tub of that Isopon Metalik lying around somewhere - if so, I will throw it in free of charge (it's about £10 in Halfords iirc), but I can't promise I have any

Sorry, I just checked and I don't have any metal filler. Forget I said anything!

I'll come and get these tonight at £60

Sorry mate, but I really can't afford to go cheaper than £80.

I'm confident I can get that for them, even if it takes me a little while longer to sell

Sold them on other forum. Got £100 for them